Samsung DC93-00278B Top Load Washer Vibration Sensor (MEMS) OEM Part

<div class="product-description dc93-00278b"> <h2>Samsung DC93-00278B Top Load Washer Vibration Sensor</h2> <p>A high-speed top-load washer needs to know exactly how its tub is moving, and in many Samsung washers that job belongs to a sensor about the size of a matchbox. The&nbsp;<strong>Samsung DC93-00278B</strong>&nbsp;is the original-equipment vibration sensor, often called the MEMS sensor, used in Samsung top-loaders from the WA48H and WA50F series to the WA54M and FlexWash models. When it stops reporting accurately, the washer plays it safe. It refuses to spin, flashes a sensor code, or keeps stopping to rebalance a load that's already fine.</p> <h3>How It Protects Your Washer</h3> <table class="part-specs"> <thead> <tr><th scope="col">Step</th><th scope="col">What Happens</th></tr> </thead> <tbody> <tr><td>1. Measure</td><td>The sensor tracks the tub's movement in real time during agitation and spin.</td></tr> <tr><td>2. Report</td><td>It sends those readings to the main control board.</td></tr> <tr><td>3. React</td><td>If the tub moves too much, the board slows the spin, adds water or redistributes the load.</td></tr> <tr><td>4. Retry</td><td>Once the load is balanced, the washer ramps back up to full spin speed.</td></tr> </tbody> </table> <p>Without accurate readings, the washer either won't spin at all or spins while shaking hard enough to damage the suspension and tub.</p> <h3>Symptoms and Causes</h3> <table class="part-specs"> <thead> <tr><th scope="col">What You Notice</th><th scope="col">What It Usually Means</th></tr> </thead> <tbody> <tr><td>Vibration or MEMS sensor code (often 8E or 8C)</td><td>Failed sensor or a loose sensor connector</td></tr> <tr><td>Unbalance message (UE or Ub) with a small load</td><td>Sensor sending bad readings, or worn suspension rods</td></tr> <tr><td>Won't spin, even with an empty tub</td><td>Sensor fault, or a lid lock or control problem</td></tr> <tr><td>Violent shaking or walking during spin</td><td>Sensor not detecting imbalance, worn suspension, or an unlevel washer</td></tr> <tr><td>Cycle runs much longer than normal</td><td>Washer repeatedly trying to rebalance</td></tr> </tbody> </table> <p>For more troubleshooting tips, see our&nbsp;<a href="https://www.deals4parts.com/help-for-appliance-troubleshooting-and-repair/">appliance troubleshooting and repair help</a>.</p> <h3>Try These Before Replacing the Sensor</h3> <ul> <li><strong>Power reset:</strong> unplug the washer for 5 minutes, then run a rinse-and-spin with the tub empty.</li> <li><strong>Rebalance the load:</strong> bulky items like comforters and bath mats can cause real imbalance.</li> <li><strong>Level the washer:</strong> all four feet should sit firmly on a solid floor.</li> <li><strong>Check the connector:</strong> a loose plug at the sensor or control board triggers the same codes.</li> <li><strong>Look at the suspension:</strong> worn rods let the tub swing too freely.</li> </ul> <p>If the sensor code returns with an empty tub after these checks, the sensor itself is the likely culprit.</p> <h3>Compatible Samsung Washers</h3> <table class="part-specs"> <thead> <tr><th scope="col">Series</th><th scope="col">Models</th></tr> </thead> <tbody> <tr><td>WV FlexWash</td><td>WV60A9900AV, WV55M9600AW</td></tr> <tr><td>WA56H</td><td>WA56H9000AP</td></tr> <tr><td>WA54M</td><td>WA54M8750AW, WA54M8750AV</td></tr> <tr><td>WA52M / WA52J</td><td>WA52M8650AW, WA52M8650AV, WA52M7750AW, WA52M7750AV, WA52J8060AW</td></tr> <tr><td>WA50M / WA50K</td><td>WA50M7450AW, WA50M7450AP, WA50K8600AW, WA50K8600AV</td></tr> <tr><td>WA50F</td><td>WA50F9A8DSW, WA50F9A8DSP, WA50F9A7DSW, WA50F9A7DSP, WA50F9A6DSW</td></tr> <tr><td>WA48J / WA48H</td><td>WA48J7775MP, WA48J7770AW, WA48J7770AP, WA48J7700AW, WA48H7400AW, WA48H7400AP</td></tr> <tr><td>Other WA models</td><td>WA5471ABP, WA5451ANW, WA484DSHASU, WA476DSHAWR, WA476DSHASU</td></tr> </tbody> </table> <p>Samsung model numbers usually end in a revision suffix such as /A2, /A4, /AA or /XAA. Look for the label under the lid or on the back of the washer. Don't see yours? Call&nbsp;<a href="tel:18669959797">866-995-9797</a>&nbsp;and we'll confirm the fit.</p> <h3>Specifications</h3> <table class="part-specs"> <tbody> <tr><th scope="row">OEM Part Number</th><td>DC93-00278B</td></tr> <tr><th scope="row">Manufacturer</th><td>Samsung (Genuine OEM)</td></tr> <tr><th scope="row">Part Type</th><td>Washer Vibration Sensor (MEMS Sensor Assembly)</td></tr> <tr><th scope="row">Used In</th><td>Samsung top-load and FlexWash washers</td></tr> <tr><th scope="row">Mounting</th><td>Outer tub</td></tr> <tr><th scope="row">Approximate Size</th><td>3.6 x 1.5 x 0.8 inches</td></tr> <tr><th scope="row">Not Interchangeable With</th><td>DC93-00278A</td></tr> <tr><th scope="row">Supersedes</th><td>AP5579308, PS4216272, 2691827</td></tr> <tr><th scope="row">Condition</th><td>Brand new</td></tr> </tbody> </table> <h3>Replacing the DC93-00278B</h3> <ol> <li>Unplug the washer and shut off both water valves.</li> <li>Open the top or rear access panel to reach the outer tub.</li> <li>Find the sensor mounted on the tub and photograph its connection.</li> <li>Unplug the connector and remove the mounting screw.</li> <li>Install the new sensor in the same spot, secure it, and reconnect the wiring.</li> <li>Close up the washer, restore water and power, and run an empty rinse-and-spin to confirm it reaches full speed without errors.</li> </ol> <p><strong>Tools:</strong> a Phillips screwdriver, a 10mm nut driver or socket, a putty knife and your phone camera.</p> <h3>Keep Spin Cycles Smooth</h3> <ul> <li>Wash heavy items with a few towels so the weight spreads evenly.</li> <li>Don't pack the tub past its recommended capacity.</li> <li>Recheck the washer's level once in a while, especially after moving it.</li> <li>If shaking continues after the new sensor is installed, have the suspension rods inspected.</li> </ul> <h3>Shop More Samsung Washer Parts</h3> <p>Browse more&nbsp;<a href="https://www.deals4parts.com/appliance-type/washer-parts">washer parts and accessories</a>&nbsp;or shop all&nbsp;<a href="https://www.deals4parts.com/brand/samsung">genuine Samsung parts</a>.</p> <h3>Why Deals4Parts</h3> <p>Deals4Parts has supplied genuine OEM appliance parts since 2010. Choose standard, next-day or 2nd-day delivery on our&nbsp;<a href="https://www.deals4parts.com/shipping-methods/">shipping methods</a>&nbsp;page. See our&nbsp;<a href="https://www.deals4parts.com/return-policy/">return policy</a>&nbsp;for returns, and use our&nbsp;<a href="https://www.deals4parts.com/file-an-extended-warranty-claim/">warranty claim</a>&nbsp;page if you need support. Questions? Call&nbsp;<a href="tel:18669959797">866-995-9797</a>&nbsp;or&nbsp;<a href="https://www.deals4parts.com/contact/">contact us</a>.</p> <h3>DC93-00278B FAQs</h3> <h4>What is a MEMS sensor on a Samsung washer?</h4> <p>It's the vibration sensor. MEMS stands for micro-electro-mechanical system, a tiny motion sensor that measures how the tub moves so the washer can detect an unbalanced load.</p> <h4>My Samsung washer shows 8E. What does that mean?</h4> <p>On many Samsung top-load washers, 8E points to a vibration sensor problem. Reset the washer and check the sensor's wiring first. If the code returns, the sensor likely needs replacing.</p> <h4>Will this fit my Samsung WA50K8600AW?</h4> <p>Yes. DC93-00278B fits the WA50K8600AW and WA50K8600AV, along with the other WA and WV models in the table above.</p> <h4>Does it fit Samsung FlexWash washers?</h4> <p>Yes. It fits the WV55M9600AW and WV60A9900AV FlexWash models.</p> <h4>Can I use DC93-00278A instead?</h4> <p>No. DC93-00278A and DC93-00278B are made for different Samsung washers. Use the number printed on your old sensor.</p> <h4>What part numbers does DC93-00278B supersede?</h4> <p>It supersedes AP5579308, PS4216272 and 2691827.</p> </div>